Store

SolarEdge P950 power optimizer from the commercial series: a single device for two modules connected in series, with 950 W input power and maximum voltage of 125 Voc. It halves the number of optimizers, cables, and installation hours on medium- and large-scale systems. Compatible only with SolarEdge SE16K and higher three-phase inverters. 2,2 m output cable, MC4 connectors, 25-year warranty.

SolarEdge S650B-1GM4MBM power optimizer: the flagship model of the residential S series, for one photovoltaic module up to 650 W nominal.Maximum input voltage 85 Vdc, MPPT 12,5-85 V, 99,5% efficiency, 15 A output current, 2,3 m output cable, curved bracket, IP68 rating, and 1 V safety voltage. 25-year warranty.

SolarEdge P601-4RM4MBN power optimizer for one high-power PV module up to 600 W, with per-module MPPT tracking and up to 99.5% peak efficiency.
MC4 connectors, IP68 rating and automatic module-level voltage shutdown for installer and firefighter safety. 25-year warranty.

SolarEdge S500B power optimizer for photovoltaic modules up to a nominal 500 W, increased to 650 W on installations after 1° April 2024.It is the high-voltage version of the S series: maximum Voc 125 Vdc, MPPT 12,5-105 V, output up to 80 V. Allows minimum strings of 6 modules on single-phase inverters. MC4 connectors, IP68, 25-year warranty.

SolarEdge S440 power optimizer (SES440-1G-M4M-RM) for one photovoltaic module up to 440 W rated, increased to 490 W for installations after 1° April 2024.MPPT at individual module level, maximum efficiency 99,5%, maximum input voltage 60 Vdc, MC4 connectors, IP68 rating, and automatic voltage shutdown to 1 V according to VDE-AR-E 2100-712. 25-year warranty.

SolarEdge Energy Bank lithium battery: 10.3 kWh nominal and 9.7 kWh genuinely usable (100% depth of discharge), round-trip efficiency up to 94.5%, 10-year warranty.DC-coupled with compatible SolarEdge inverters: a single conversion, fewer losses. 5 kW continuous power, 7.5 kW peak in backup. IP55, for indoor or outdoor installation, expandable up to 3 batteries.

SolarEdge Home 48V BAT-05K48M0B-02 Battery: 4,6 kWh fully usable (100% DoD) lithium LFP storage module, DC-coupled to SolarEdge Home Hub and StorEdge three-phase inverters.
Discharge power up to 4.096 W per single module, cycle efficiency over 95%, IP65 rating for indoor or outdoor installation, and noise level below 25 dBA. Stackable up to 5 modules (23 kWh). 10-year warranty.

Three-phase AC panel 8/11 kW with IMTD 4x20 A class A 300 mA, IMT input/output switch-disconnector and class II SPD surge arrester 4P 400 V - 15 kA in an IP65 18-module box, with single-line diagram and Di.co. It is the last size in the series that remains below the 11,08 kW threshold of the simplified CEI 0-21 procedure: it does not include an SPI or DDI contactor, because at this power level the inverter interface protection is sufficient.

CEI 0-21 interface panel for photovoltaic systems from 75 to 95 kW on one inverter, rated current 160 A at 400 V. Includes SPI, 140 A-AC3 DDI contactor, IMTD 4x160 A-10 kA with DDR backup, inverter protection IMT, SPD surge arrester and fuse holders dedicated to SPI power supply and measurements, in IP66 enclosure with 140 modules. Supplied with single-line diagram, Di.co and SPI test report.

Three-phase AC panel 6/8 kW for protecting the AC line downstream of the photovoltaic inverter: IMTD 4x16 A class A 300 mA and class II SPD surge arrester 4P 400 V - 15 kA in an IP65 18-module box, with single-line diagram and declaration of conformity Di.co. Does not contain SPI or DDI contactor: on systems up to 11,08 kW, the interface protection integrated in the inverter is sufficient according to CEI 0-21.

Three-phase interface panel from 56 to 70 kW, 125 A, compliant with CEI 0-21: the largest size in the low-voltage series. SPI relay calibrated and tested at the factory with SPI test report included.IP66 class II enclosure with 96 DIN modules (540 × 640 × 240 mm). Check on the distributor's quotation that the connection point is in LV: in medium voltage a CEI 0-16 solution is required.

Three-phase interface panel from 45 to 55 kW, 100 A, compliant with CEI 0-21 for industrial photovoltaic systems connected in low voltage. SPI relay calibrated and tested at the factory, with SPI test report included.IP66 class II enclosure with 96 DIN modules (540 × 640 × 240 mm): enough spare space for meters, monitoring auxiliaries and future expansions.

Three-phase QAC 36/44 kW interface cabinet for PV systems from 36 to 44 kW, compliant with the Italian standard CEI 0-21.54-module enclosure, 480x540x220 mm, IP66 class II: it integrates main device, interface device, interface protection and surge arrester in a single pre-wired, factory-tested unit. Supplied with wiring diagram, declaration of conformity and SPI test report.

Three-phase interface panel from 21 to 25 kW, compliant with CEI 0-21, with Interface Protection System (SPI) and test report included: mandatory above the 11,08 kW threshold, where the protections built into the inverter are no longer sufficient for the distributor.IP65 enclosure in insulation class II, 36 DIN modules, 440 × 460 × 140 mm.

Three-phase interface panel from 12 to 15 kW, 25 A 400 V, compliant with CEI 0-21 for one inverter. Integrates the Interface Protection System (SPI), the contactor interface device, the Class A residual-current circuit breaker with overcurrent protection, and the surge arrester.36-module IP65 box, supplied with single-line diagram, declaration of conformity, and SPI test report: the three documents required by the distributor for connection.

Single-phase AC protection panel for 5 to 6 kW photovoltaic systems, 32 A 230 V: the maximum size allowed on a single-phase connection. It integrates a Class A 32 A 300 mA residual current circuit breaker with overcurrent protection, switch in in/out configuration, and Class II 2P 230 V 15 kA SPD surge protector.Compact IP65 8-module box with single-line diagram and declaration of conformity.

Single-phase AC protection panel for 3 to 5 kW photovoltaic systems, 25 A 230 V. Integrates a 300 mA Class A RCBO and Class II SPD surge arrester 2P 230 V 15 kA.12-module IP65 box with single-line diagram and declaration of conformity. It is a protection and disconnection panel: the interface protection remains the one integrated in the inverter.

Single-phase AC protection panel for photovoltaic systems from 1 to 3 kW, 16 A 230 V. Integrates a 300 mA Class A residual current circuit breaker with overcurrent protection, in/out configuration and Class II SPD surge arrester 2P 230 V 15 kA.12-module IP65 box, supplied with single-line diagram and declaration of conformity. It does not include interface protection: it is designed for systems below the 11,08 kW threshold.

IP66 fiberglass DC field box for 9 strings at 1000 V, 20 A. DC breakers with shunt trip coil for remote or emergency tripping, 72-module box with transparent door. For commercial arrays.

DC field box for 6 independent strings (6 IN / 6 OUT) up to 1000 V, to be installed between the photovoltaic modules and the inverter. It integrates disconnectable fuse holders, 1000 V DC switch-disconnectors and surge protection devices for each string, with separate input and output terminal blocks.
IP65 enclosure for 36 modules with component labeling on plastic-coated rails.