List of products by brand Solaredge

SolarEdge S440 power optimizer (SES440-1G-M4M-RM) for one photovoltaic module up to 440 W rated, increased to 490 W for installations after 1° April 2024.MPPT at individual module level, maximum efficiency 99,5%, maximum input voltage 60 Vdc, MC4 connectors, IP68 rating, and automatic voltage shutdown to 1 V according to VDE-AR-E 2100-712. 25-year warranty.

SolarEdge S500B power optimizer for photovoltaic modules up to a nominal 500 W, increased to 650 W on installations after 1° April 2024.It is the high-voltage version of the S series: maximum Voc 125 Vdc, MPPT 12,5-105 V, output up to 80 V. Allows minimum strings of 6 modules on single-phase inverters. MC4 connectors, IP68, 25-year warranty.

SolarEdge S500 power optimizer (SES500-1G-M4M-RM) for one photovoltaic module up to 500 W rated, increased to 550 W for installations after April 1, 2024.Maximum efficiency 99.5%, maximum input voltage 60 Vdc, MPPT 8-60 V, MC4 connectors, IP68 rating and 1 V safety voltage according to VDE-AR-E 2100-712. 25-year warranty.

SolarEdge P601-4RM4MBN power optimizer for one high-power PV module up to 600 W, with per-module MPPT tracking and up to 99.5% peak efficiency.
MC4 connectors, IP68 rating and automatic module-level voltage shutdown for installer and firefighter safety. 25-year warranty.

SolarEdge S650B-1GM4MBM power optimizer: the flagship model of the residential S series, for one photovoltaic module up to 650 W nominal.Maximum input voltage 85 Vdc, MPPT 12,5-85 V, 99,5% efficiency, 15 A output current, 2,3 m output cable, curved bracket, IP68 rating, and 1 V safety voltage. 25-year warranty.

SolarEdge P950 power optimizer from the commercial series: a single device for two modules connected in series, with 950 W input power and maximum voltage of 125 Voc. It halves the number of optimizers, cables, and installation hours on medium- and large-scale systems. Compatible only with SolarEdge SE16K and higher three-phase inverters. 2,2 m output cable, MC4 connectors, 25-year warranty.

SolarEdge Home 48V BAT-05K48M0B-02 Battery: 4,6 kWh fully usable (100% DoD) lithium LFP storage module, DC-coupled to SolarEdge Home Hub and StorEdge three-phase inverters.
Discharge power up to 4.096 W per single module, cycle efficiency over 95%, IP65 rating for indoor or outdoor installation, and noise level below 25 dBA. Stackable up to 5 modules (23 kWh). 10-year warranty.

SolarEdge Energy Bank lithium battery: 10.3 kWh nominal and 9.7 kWh genuinely usable (100% depth of discharge), round-trip efficiency up to 94.5%, 10-year warranty.DC-coupled with compatible SolarEdge inverters: a single conversion, fewer losses. 5 kW continuous power, 7.5 kW peak in backup. IP55, for indoor or outdoor installation, expandable up to 3 batteries.

IAC-RBAT-5KFSTD-01 floor stand for SolarEdge Home 48V (BAT-05K48) battery towers. Optional accessory, one is required per tower and not one per module: it raises the storage system by 50 mm from the floor, useful against water ingress and on surfaces that are not perfectly level. The tower remains 540 mm wide and 240 mm deep.

IAC-RBAT-5KCBAT-01 battery-to-battery cable set for SolarEdge Home 48V storage: contains 2 DC cables, 1 communication cable and 1 grounding cable. One set is required for each additional module in the tower: none with a single battery, one with two modules, two with three modules. The connection to the inverter requires a different accessory.

Battery-to-inverter cable set IAC-RBAT-5KCINV-01 for SolarEdge Home 48V storage. This is the version for inverters in the Home Hub line with code SE*K-RWB48 (SE5K, SE8K, SE10K): it is not compatible with StorEdge SE*K-RWS inverters, which require the -02 version. One is required per battery tower.

Battery-to-inverter cable set IAC-RBAT-5KCINV-02 for SolarEdge Home 48V storage, in the version for StorEdge inverters with code SE*K-RWS. Contains 2 DC cables, 1 communication cable and 1 grounding cable. It is not compatible with Home Hub SE*K-RWB48 inverters, for which the -01 version is required. One is needed per tower.

IAC-RBAT-5KCTOW-01 tower-to-tower cable set for SolarEdge Home 48V storage: 2 DC cables, 1 communication cable and 1 grounding cable, with longer lengths than the battery-to-battery set. It is required when the modules are distributed across two separate columns, a typical setup with more than three modules per tower. It is not interchangeable with the IAC-RBAT-5KCBAT-01 set.

IAC-RBAT-5KMTOP-01 top cover for SolarEdge Home 48V (BAT-05K48) battery towers. Unlike the floor stand, it is required, and one is needed per tower regardless of the number of modules: just one even for a column of three batteries, two if the storage system is split across two towers. The heights published by SolarEdge already include it.

Energy Net Kit ENET-HBCL-01 for wireless communication between SolarEdge inverters, the Energy Bank battery, and SolarEdge Home devices. This is the version for inverters with SetApp not Energy Net ready configuration (codes with BN) and also includes the compatible communication board. One per inverter is required. It occupies the cellular card slot and cannot coexist with the ZigBee module.

Energy Net ENET-HBNP-01 plug-in module for wireless communication between SolarEdge inverters, Energy Bank battery and SolarEdge Home devices. This is the version for inverters already Energy Net ready (codes with BE), so it does not include the communication board and costs less than the complete kit. One is required per inverter. External antenna included.

SolarEdge ENET-HBPV3D-01 upgrade kit: includes communication board with LCD display, SolarEdge Home Network plug-in and antenna.
It brings single-phase HD-Wave inverters with display (not Home Network ready from the factory) up to the current communication standard, enabling the SolarEdge Home Battery / Energy Bank and wireless control of Smart Energy devices.

SolarEdge IAC-RBAT-FLRSTD-01 floor stand kit for the Energy Bank / SolarEdge Home Battery 10 kWh.
It includes the base mount and the rear holder and is the alternative to wall mounting when the wall is not suitable. One kit per battery; multiple stands can be placed side by side and secured to each other.

IAC-RBAT-HANDLE-01 handle for handling the SolarEdge Energy Bank battery, especially useful for wall mounting. The package contains 1 piece, but 4 are required per battery: this is the most common ordering mistake for this accessory. It is not part of the final installation and can be reused for subsequent jobs.

SolarEdge IAC-RBAT-RWYCBL-01 Y-cable kit for connecting multiple Home 48V batteries in parallel to the same Home Hub or StorEdge inverter. Dedicated MC4 connectors, not replaceable with generic adapters.