Lithium batteries

SolarEdge Home 48V BAT-05K48M0B-02 Battery: 4,6 kWh fully usable (100% DoD) lithium LFP storage module, DC-coupled to SolarEdge Home Hub and StorEdge three-phase inverters.
Discharge power up to 4.096 W per single module, cycle efficiency over 95%, IP65 rating for indoor or outdoor installation, and noise level below 25 dBA. Stackable up to 5 modules (23 kWh). 10-year warranty.

SolarEdge Energy Bank lithium battery: 10.3 kWh nominal and 9.7 kWh genuinely usable (100% depth of discharge), round-trip efficiency up to 94.5%, 10-year warranty.DC-coupled with compatible SolarEdge inverters: a single conversion, fewer losses. 5 kW continuous power, 7.5 kW peak in backup. IP55, for indoor or outdoor installation, expandable up to 3 batteries.

IAC-RBAT-5KFSTD-01 floor stand for SolarEdge Home 48V (BAT-05K48) battery towers. Optional accessory, one is required per tower and not one per module: it raises the storage system by 50 mm from the floor, useful against water ingress and on surfaces that are not perfectly level. The tower remains 540 mm wide and 240 mm deep.

IAC-RBAT-5KCBAT-01 battery-to-battery cable set for SolarEdge Home 48V storage: contains 2 DC cables, 1 communication cable and 1 grounding cable. One set is required for each additional module in the tower: none with a single battery, one with two modules, two with three modules. The connection to the inverter requires a different accessory.

Battery-to-inverter cable set IAC-RBAT-5KCINV-01 for SolarEdge Home 48V storage. This is the version for inverters in the Home Hub line with code SE*K-RWB48 (SE5K, SE8K, SE10K): it is not compatible with StorEdge SE*K-RWS inverters, which require the -02 version. One is required per battery tower.

Battery-to-inverter cable set IAC-RBAT-5KCINV-02 for SolarEdge Home 48V storage, in the version for StorEdge inverters with code SE*K-RWS. Contains 2 DC cables, 1 communication cable and 1 grounding cable. It is not compatible with Home Hub SE*K-RWB48 inverters, for which the -01 version is required. One is needed per tower.

IAC-RBAT-5KCTOW-01 tower-to-tower cable set for SolarEdge Home 48V storage: 2 DC cables, 1 communication cable and 1 grounding cable, with longer lengths than the battery-to-battery set. It is required when the modules are distributed across two separate columns, a typical setup with more than three modules per tower. It is not interchangeable with the IAC-RBAT-5KCBAT-01 set.

IAC-RBAT-5KMTOP-01 top cover for SolarEdge Home 48V (BAT-05K48) battery towers. Unlike the floor stand, it is required, and one is needed per tower regardless of the number of modules: just one even for a column of three batteries, two if the storage system is split across two towers. The heights published by SolarEdge already include it.

Energy Net Kit ENET-HBCL-01 for wireless communication between SolarEdge inverters, the Energy Bank battery, and SolarEdge Home devices. This is the version for inverters with SetApp not Energy Net ready configuration (codes with BN) and also includes the compatible communication board. One per inverter is required. It occupies the cellular card slot and cannot coexist with the ZigBee module.

Energy Net ENET-HBNP-01 plug-in module for wireless communication between SolarEdge inverters, Energy Bank battery and SolarEdge Home devices. This is the version for inverters already Energy Net ready (codes with BE), so it does not include the communication board and costs less than the complete kit. One is required per inverter. External antenna included.

SolarEdge ENET-HBPV3D-01 upgrade kit: includes communication board with LCD display, SolarEdge Home Network plug-in and antenna.
It brings single-phase HD-Wave inverters with display (not Home Network ready from the factory) up to the current communication standard, enabling the SolarEdge Home Battery / Energy Bank and wireless control of Smart Energy devices.

SolarEdge IAC-RBAT-FLRSTD-01 floor stand kit for the Energy Bank / SolarEdge Home Battery 10 kWh.
It includes the base mount and the rear holder and is the alternative to wall mounting when the wall is not suitable. One kit per battery; multiple stands can be placed side by side and secured to each other.

IAC-RBAT-HANDLE-01 handle for handling the SolarEdge Energy Bank battery, especially useful for wall mounting. The package contains 1 piece, but 4 are required per battery: this is the most common ordering mistake for this accessory. It is not part of the final installation and can be reused for subsequent jobs.

SolarEdge IAC-RBAT-RWYCBL-01 Y-cable kit for connecting multiple Home 48V batteries in parallel to the same Home Hub or StorEdge inverter. Dedicated MC4 connectors, not replaceable with generic adapters.

SolarEdge SE-BI-EU 1P Backup Interface (BI-EU1P) for full or partial home backup on single-phase Home Hub inverters with battery. IP65, up to 100 A and 3 inverters in parallel. To be purchased separately from the inverter.

SolarEdge SE-BI-EU 3P (BI-EU3P) backup interface for full or partial home backup on three-phase Home Hub inverters with battery. Integrated meter, IP65, 12-year warranty. To be purchased separately from the inverter.

ZCS Azzurro ZSX5000-S LiFePO4 lithium battery (ZZT-BAT-5KWH-Z5S), nominal capacity 5,1 kWh, compatible with single-phase HYD-HP inverter 3,6-6 kW. IP65, up to 4 modules in parallel, 10-year warranty.

Battery Distribution Unit (BDU) for ZCS Azzurro high voltage storage systems using 5.1 kWh ZBT 5K modules. It is the base unit of the tower, housing the BMS, the DC protection devices and the link to the inverter.
IP65 rated, inverter connection cables included. One BDU is required per battery tower, with 1-4 modules per tower.

Single-phase all-in-one storage system from ZCS Azzurro for retrofit: a 2.5 kW inverter and a 5.12 kWh LiFePO4 lithium battery in a single wall-mounted appliance.
AC coupled: it is added to an existing photovoltaic system without replacing the inverter. Expandable with several units in parallel.

High-voltage battery module ZCS Azzurro ZZT-BAT-ZBT5K, 5,12 kWh nominal, 400V, stackable up to 4 modules (20,48 kWh). Compatible with ZP1 and ZP3 inverters. IP65, external BDU required.